ntbackup
Under WindowsNT and Windows2000 filesystem backups are done using the
ntbackup
program. This is a GUI tool with easy to
use wizards to get you started, but it is also accessible from the command line. The command line parameters differ between WindowsNT
and Windows2000. Under WindowsNT a typical backup command would look like:
ntbackup backup c:\ /d "Daily Backup" /hc:on /l "C:\backup.log" /e /t normal /v
c:\ : The drive to backup.
/d "Daily Backup" : The name of the backup set.
/hc:on : Harware compression on.
/l "C:\backup.log" : Location of the logfile.
/e : Log exceptions only.
/t normal : Backup type normal.
/v : Verify backup.
Under Windows2000 a similar command would look like:
ntbackup backup c:\ /D "Daily Backup" /HC:on /L:s /M normal /P DLT /V:yes /UM
c:\ : The drive to backup.
/D "Daily Backup" : The name of the backup set.
/HC:on : Harware compression on.
/L:s : Summary data only in log.
/M normal : Backup type normal.
/P DLT : Media pool assignment (Backup/DLT).
/V:yes : Verify backup.
/UM : Unmanaged.
The Windows2000 backup logs always appear in:
C:\Documents and Settings<user-name>Local Settings\Application Data\Microsoft\Windows NT\NTbackup\Data
Where user-name is the user who ran ntbackup.
The Windows2000 is rather troublesome regarding reuse of tapes. Using the following procedure should alleviate most of these problems:
- From the task bar click "Start" -> "Run..."
- Enter "ntbackup" and click "OK".
- From the ntbackup menu select "Tools" -> "Options" and click on the "General" tab.
- Check the "Always move new import mediato the Backup media pool" option and click "OK".
- Exit ntbackup.
If there are still issues you must right-click the appropriate tape drive in "Computer Management" and select the
"Mark as clean" option. At this point the tape should be reused properly.
tar
The
tar
command can be used to backup and restore files to another filesystem or an offile storage device:
# Create archive.
cd /u01/app/oracle
tar -cvf /tmp/admin.tar admin
# Restore archive.
cd /tmp
tar -xvf admin.tar
If a full path is used during the archive creation the extract locations are fixed rather than relative. The process is similar
when accessing a tape device except the destination is the mounted device:
# Mount and rewind the tape.
mt -f /dev/rmt/2m rew
# Create archive.
tar -cvf /dev/rmt/2m /u01/*
# Restore archive.
tar -xvf /dev/rmt/2m
dd
The
dd
command is similar to the tar command:
# Mount and rewind the tape.
mt -f /dev/rmt/2m rew
# Create archive.
dd if=/u01/app/oracle/* of=/dev/rmt/2m BS=32K
# Restore archive.
dd if=/dev/rmt/2m of=/u01/app/oracle BS=32K
cpio
The
cpio
command deals with the standard input so filesystem paths must be piped to it:
# Create archive.
cd /u01/app/oracle
find admin | cpio -oc > /tmp/admin.cpio
# Restore archive.
cd /tmp
cpio -idmv <>
If a full path is used during the archive creation the extract locations are fixed rather than relative:
find /u01/app/oracle/admin | cpio -oc > /tmp/admin.cpio
vdump, rvdump, vrestore and rvrestore
Full level 0 backup of a local filesystem (/u01) to a local device (/dev/tape/tape1_d6):
/sbin/vdump -0 -u -f /dev/tape/tape1_d6 /u01
Full level 0 backup of a local filesystem (/u01) to a remote device (server2:/dev/tape/tape1_d6):
/sbin/rvdump -0 -u -f server2:/dev/tape/tape1_d6 /u01
Restore a vdump or rvdump archive from a local device (/dev/tape/tape1_d6) to a local filesystem (/u01):
/sbin/vrestore -xf /dev/tape/tape1_d6 -D /u01
Restore a vdump or rvdump archive from a remote device (server2:/dev/tape/tape1_d6) to a local filesystem (/u01):
/sbin/rvrestore -xf server2:/dev/tape/tape1_d6 -D /u01
0 Comment :
Post a Comment